So if you’ve been reading this a while you’ll know I bought 3 dead C64s. I managed to get one working by cleaning the power switch. (Cleaning the switch also got the next two working closer to full completion). The second one I got working by taking the RAM out of the third, which was showing symptoms much worse than the other two.
The third one was just sitting there, taunting me with a black screen and nothing else.
I did some research and it turns out the fault was likely to be one of 3 chips. Two of those chips were pretty reliable and also insanely expensive to replace, so I ordered the third chip (The PLA) on a whim and some new RAM. (Apparently, yes, you can buy new RAM for C64s. Who knew?)
All those parts arrived today.
I then took my “good” C64 (the middle one) and socketed it’s PLA. (I had already socketed the RAM chip). This allowed me to test the new components in a known good machine. The new parts all worked fine.
So I socketed up the third machine and tried the RAM and PLA in there. It worked first time!
So now I have FOUR working Commodore 64s. This is 4 more than I had this time last year 😀
(Big shoutout to Shrydar for allowing me to buy his old parts for an excellent price)
So the Pi1541 arrived and I am amazed how useful it is. It’s not 100% compatible yet, but gets better every week. I LUFF it. I’ve built the PSU for the 1541 floppy drive and that drive is currently formatting up disks in the background. The C128D monitor is fixed, but I need to build a stand for it as otherwise I won’t have any desk at all. I also need to replace the failed switch with a working switch I just found. I’ll need to order parts for the second 1541 PSU and C64 PSU. I’m really tempted to build a “pure” C64 PSU as per Greisis Workshop After that it’s probably time to rejoin Artifactory, except for the small issue of their laser cutters being out of action AGAIN.
Well, let’s see. I’m a LOT better at all this stuff. I have the A1200 booting, and more! It has:
A proper LCD monitor that supports the wonky frequencies the Amiga uses (15KHz vertical refresh).
An SD to HDD adapter, with an 8GB SD card in there pretending to be a couple of hard disks.
A keyboard adapter allowing me to use an old PS/2 keyboard with it.
A mouse adapter that I designed and made that allows me to automagically change to a joystick in the same port.
A Virtual Floppy drive (Works from USB thumbdrives full of disk images) that I flashed the firmware of and added all the extras such as
An OLED screen that shows me which image I’m using.
A pizeo speaker that simulates the buzzes and clicks of the original.
A rotary selector that makes disk choosing easy.
A design for a laser cut case to hold it all, only pending the Artifactory fixing their damned lasers again.
I also purchased a batch lot of Commodore stuff and now have:
A Commodore 64 (More on this later)
A Vic 20 (With a whole bunch of carts)
An SX64 with what appears to be a dead PSU
A Commodore 128D. This is a “Work in Progress” as it has a problem. I’ve recapped it but it fails when I plug the PSU back in. Basically I need to take it to the Artifactory and plug it into the bench PSU.
2 Floppy drives, one of which definitely works, one of which needs some more love.
2 Printers(!) that I’ll need to gove some love to once I have everything else under control
A C128 Monitor which has a loud scary crackle.
I had to build a new PSU for the C64 and Vic20 as the “stock” ones are notoriously bad. They have a nasty “fail to high voltage” that’s really efficient at cooking chips. This was an interesting challenge but I got there in the end. I’m always a bit squirrelley around AC voltage.
I then purchased a job lot of dead Commodore stuff. 3 C64s and another FDD plus a joystick. This was for a fraction of the price I paid for the batch job above, but that was cos it was all failed stuff.
So initially I plugged all three C64s in one by one and documented the faults. Two had a problem where I got monitor sync and nothing else. One had zip. Nada. Nothing. Doing standard fault finding I found the first two had no DC voltage and the second had no AC voltage. Turns out the switches on C64s have an effective lifespan of about 20 years… These were 1986 models. I had to desolder the switches, which turns out to be one of those understatement things like “And then the atomic bomb exploded” as Commodore must have hated their service technicians. There is an RF shield that’s soldered on to the motherboard. I manged to desolder the RF Shield through a combination of my soldering iron on maximum and using a set of dental picks as prys. Once THAT was off my desoldering station made quick work of the switches. I desoldered, cleaned, greased and assembled and suddenly 2 of the 3 were booting! The third was now getting sync. Of the two booting ones, one was perfect. It’s now in my stack of “working” gear waiting for a recapping. I’ll probably sell one of the working ones. The other was showing rainbow garbage, an issue consistent with bad RAM. This led to more purchases. I next purchased a couple of cartridges (Dead Test, 60 in 1) and some bits and pieces.
My next project was to build a pair of paddles for the C64. Unfortunately I haven’t had a chance to test them yet.
I used the Dead Test to confirm which chips were bad in the dead RAM c64 and I decided to use the OTHER dead c64 as a parts donor (As it was showing fatality on one of the key chips)
I have, however, been unable to desolder the RAM off my sacrifice board! I’ll try again this weekend if I can but it’s more challenging than I would have expected. After half an hour I’ve manged to get ONE of the chips to sit at a jaunty angle and that’s it.
Still to do:
I need to build a pair of 1541 ii PSUs. I have the parts for one but will need to order more bits.
I need to recap all of the c64s
I need to build more PSUs for c64s
I need to get to the Artifactory and test what’s wrong with the c128D and get it working!
I need to get my c128D monitor to the guy who has offered to have a look at it.
Stuff “in the mail”
Utility cart (Including Fastload, Freeze and loads more stuff)
Pi1541 (This is an awesome doodad you plug into a Raspberry Pi and it emulates a Floppy Drive.
What have I been up to? Well, a bit of this and a bit of that. Picked up a new hobby, BTW.
What’s that? You wanna know more about my new hobby? OK.
So after watching many YouTubers playing with classic computers I decided I wanted in. I’d recently acquired an Amiga CD32, which I got recapped (It was all SMT so I wasn’t going to do it I can tell you) so I had a foot in the door. I built a new PSU for it and I had a working console but I wanted MOAR! At Swancon I asked around and a friend came to the party as she had a few more systems gathering dust. (I won’t name her to respect her privacy) This netted me an N64, a NES and, most interestingly a Sinclair ZX Spectrum. Meanwhile I ordered an Amiga 1200 off AmiBay in a semi-working state (Don’t ask how much it cost. I’m mostly using it for parts.) which took three months to get here. I have had some leave recently, so in a flurry I have: Recapped the NES and the Spectrum Purchased a new PSU for the Spectrum. Replaced the cartridge connector on the NES <- At this point it was working. Converted the Spectrum to use Composite out rather than TV Out. <- At this point the spectrum was booting.
The Spectrum needed much more work. Although it was booting, the keyboard was unreliable. It was in an aftermarket case which meant I didn’t need to deal with the notorious membrane. This took me ages to fix as it was multiple issues overlapping. Firstly, all the contacts were corroded. This was solved with some contact cleaner, a bamboo chopstick (They make excellent “soft” contact cleaners) and some strips of cardboard. Secondly, some of the wires on the keyboard connectors had poor solder joints. I desoldered / resoldered them and that fixed that. I needed to also trim the edge of one of the connectors to ensure a better electrical connection with the motherboard. Now I could boot and type. It took me a while to work out exactly HOW to load a game, and I didn’t have a tape deck in a working state. I solved this issue by using my Android phone, a piece of software called “TeeZiX”, and an eeevil custom made cable. Now I could even load games. This is the point one of the key buttons on the keyboard stopped working. Thankfully I was able to resolve that with some contact cleaner. I was loading games! I was even playing them! W00t!
My next step is to wait until next month so I can afford to buy another PSU to hack into the Amiga 1200. I think at this point I should be able to get it to boot to the “Insert Disk” screen (I hope). I’m not sure how I’m going to proceed from there to be honest. My big challenge will be getting bootdisks ready to boot the Amiga to the point where I can format and install an OS. The Amiga uses a non-standard floppy disk format (880K) that I may need to build a USB to FDD bridge just so I can write out the disks from images.
So that’s kept me busy.
Oh, and if you happen to have an old C64, C128, or an Amstrad CPC machine you no longer want / love, let me know 🙂
This is a brand new blogsite. I’ll be bringing content across from other sites as I go forrward.
So what are we doing here? Well, I had content scattered across thing such as e-mails, websites and even LinkedIn. None of it was in one place. This page will consolidate all my musings and experiences with RetroComputing.